RESUMEN
The relative abundance of light elements in the Earth's core has long been controversial. Recently, the presence of carbon in the core has been emphasized, because the density and sound velocities of the inner core may be consistent with solid Fe7C3. Here we report the longitudinal wave velocity of liquid Fe84C16 up to 70 GPa based on inelastic X-ray scattering measurements. We find the velocity to be substantially slower than that of solid iron and Fe3C and to be faster than that of liquid iron. The thermodynamic equation of state for liquid Fe84C16 is also obtained from the velocity data combined with previous density measurements at 1 bar. The longitudinal velocity of the outer core, about 4% faster than that of liquid iron, is consistent with the presence of 4-5 at.% carbon. However, that amount of carbon is too small to account for the outer core density deficit, suggesting that carbon cannot be a predominant light element in the core.
RESUMEN
A melt has greater volume than a silicate solid of the same composition. But this difference diminishes at high pressure, and the possibility that a melt sufficiently enriched in the heavy element iron might then become more dense than solids at the pressures in the interior of the Earth (and other terrestrial bodies) has long been a source of considerable speculation. The occurrence of such dense silicate melts in the Earth's lowermost mantle would carry important consequences for its physical and chemical evolution and could provide a unifying model for explaining a variety of observed features in the core-mantle boundary region. Recent theoretical calculations combined with estimates of iron partitioning between (Mg,Fe)SiO(3) perovskite and melt at shallower mantle conditions suggest that melt is more dense than solids at pressures in the Earth's deepest mantle, consistent with analysis of shockwave experiments. Here we extend measurements of iron partitioning over the entire mantle pressure range, and find a precipitous change at pressures greater than â¼76 GPa, resulting in strong iron enrichment in melts. Additional X-ray emission spectroscopy measurements on (Mg(0.95)Fe(0.05))SiO(3) glass indicate a spin collapse around 70 GPa, suggesting that the observed change in iron partitioning could be explained by a spin crossover of iron (from high-spin to low-spin) in silicate melt. These results imply that (Mg,Fe)SiO(3) liquid becomes more dense than coexisting solid at â¼1,800 km depth in the lower mantle. Soon after the Earth's formation, the heat dissipated by accretion and internal differentiation could have produced a dense melt layer up to â¼1,000 km in thickness underneath the solid mantle. We also infer that (Mg,Fe)SiO(3) perovskite is on the liquidus at deep mantle conditions, and predict that fractional crystallization of dense magma would have evolved towards an iron-rich and silicon-poor composition, consistent with seismic inferences of structures in the core-mantle boundary region.
RESUMEN
Earth's solid inner core is mainly composed of iron (Fe). Because the relevant ultrahigh pressure and temperature conditions are difficult to produce experimentally, the preferred crystal structure of Fe at the inner core remains uncertain. Static compression experiments showed that the hexagonal close-packed (hcp) structure of Fe is stable up to 377 gigapascals and 5700 kelvin, corresponding to inner core conditions. The observed weak temperature dependence of the c/a axial ratio suggests that hcp Fe is elastically anisotropic at core temperatures. Preferred orientation of the hcp phase may explain previously observed inner core seismic anisotropy.
RESUMEN
The advanced argon ion-milling technique using a new instrument called ion slicer was newly developed for preparation of thin foil. Compared to the conventional ion-milling methods, this technique facilitates very wide area to be homogeneously thinned by rocking the ion beam source with low angle and the specimen during milling. Here we applied this technique to a sample recovered from a laser-heated diamond-anvil cell (DAC). We obtained the thin film of almost entire cross section of the DAC sample along the compression axis, which possesses of approximately (10x50) microm(2). The laser-heated sample is often heterogeneous due to a large temperature gradient. However the chemical analyses are obtained from the whole hot spot under the transmission electron microscope by preparing the thin foil using the ion slicer.
